收藏本站
AT25080B/160B
Table 2-3.
AC Characteristics (Continued)
Applicable over recommended operating range from T AI = – 40 ? C to +85 ? C, V CC = As Specified,
CL = 1 TTL Gate and 30pF (unless otherwise noted)
Symbol
Parameter
Voltage
Min
Max
Units
4.5–5.5
0
25
t LZ
HOLD to Output Low Z
2.5–5.5
0
50
ns
1.8–5.5
4.5–5.5
0
100
40
t HZ
HOLD to Output High Z
2.5–5.5
80
ns
1.8–5.5
4.5–5.5
200
40
t DIS
Output Disable Time
2.5–5.5
80
ns
1.8–5.5
4.5–5.5
200
5
t WC
Write Cycle Time
2.5–5.5
5
ms
1.8–5.5
5
Endurance (1)
3.3V, 25°C, Page Mode
1M
Write Cycles
Note:
3.
1. This parameter is characterized and is not 100% tested
Serial Interface Description
MASTER: The device that generates the serial clock.
SLAVE: Because the Serial Clock pin (SCK) is always an input, the AT25080B/160B always operates as a slave.
TRANSMITTER/RECEIVER: The AT25080B/160B has separate pins designated for data transmission (SO) and
reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
SERIAL OP-CODE: After the device is selected with CS going low, the first byte will be received. This byte con-
tains the op-code that defines the operations to be performed.
INVALID OP-CODE: If an invalid op-code is received, no data will be shifted into th e AT25080B/160B, and the
serial output pin (SO) will remain in a high impedance state until the falling edge of CS is detected again. This will
reinitialize the serial communication.
CHIP SELECT: The AT25080B/160B is selected when the CS pin is low. When the device is not selected, data will
not be accepted via the SI pin, and the serial output pin (SO) will remain in a high impedance state.
HOLD: The HOLD pin is used in conjunction with the CS pin to select the AT25080B/160B. When the device is
selected and a serial sequence is underway, HOLD can be used to pause the serial communication with the mas-
ter device without resetting the serial sequence. To pause, the HOLD pin must be brought low while the SCK pin is
low. To resume serial communication, the HOLD pin is brought high while the SCK pin is low (SCK may still toggle
during HOLD). Inputs to the SI pin will be ignored while the SO pin is in the high impedance state.
WRITE PROTECT: The write protect pin (WP) will allow normal read/write operations when held high. When the
WP pin is brought low and WPEN bit is “1”, all write operations to the status register are inhibited. WP going low
while CS is still low will interrupt a write to the status register. If the internal write cycle has already been initiated,
WP going low will have no effect on any write operation to the status register. The WP pin function is blocked when
the WPEN bit in the status register is “0”. This will allow the user to install t h e AT25080B/160B in a system with the
WP pin tied to ground and still be able to write to the status register. All WP pin functions are enabled when the
WPEN bit is set to “1”.
5
5228E–SEEPR–3/12
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT25256B-SSHL-B IC EEPROM 256KBIT 20MHZ 8SOIC
AT25256T2-10TI-2.7 IC EEPROM 256KBIT 3MHZ 20TSSOP
AT25320AY6-10YH-1.8 IC EEPROM 32KBIT 20MHZ 8DFN
AT25640T1-10TI-2.7 IC EEPROM 64KBIT 3MHZ 14TSSOP
AT25DF321-SU IC FLASH 32MBIT 70MHZ 8SOIC
AT25F1024AN-10SU-2.7 IC FLASH 1MBIT 33MHZ 8SOIC
AT25F2048N-10SU-2.7 IC FLASH 2MBIT 33MHZ 8SOIC
AT25F4096W-10SU-2.7 IC FLASH 4MBIT 33MHZ 8SOIC
相关代理商/技术参数
AT25160BY6-YH-T 功能描述:电可擦除可编程只读存储器 Serial 电可擦除可编程只读存储器 16K, Mini Map, 1.8V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT25160N-10SA-2.7C 制造商:未知厂家 制造商全称:未知厂家 功能描述:SERIAL EEPROM|2KX8|CMOS|SOP|8PIN|PLASTIC
AT25160N-10SA-5.0C 制造商:未知厂家 制造商全称:未知厂家 功能描述:SERIAL EEPROM|2KX8|CMOS|SOP|8PIN|PLASTIC
AT25160N-10SC 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:SPI Serial EEPROMs
AT25160N-10SC-1.8 功能描述:IC EEPROM 16KBIT 3MHZ 8SOIC RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:378 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:8M（1M x 8，512K x 16） 速度:110ns 接口:并联 电源电压:2.7 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-CBGA 供应商设备封装:48-CBGA（7x7） 包装:托盘
AT25160N-10SC-2.7 功能描述:电可擦除可编程只读存储器 RO 511-M95160-WMN6 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT25160N-10SE-2.7 制造商:未知厂家 制造商全称:未知厂家 功能描述:EEPROM
AT25160N-10SI 制造商:Atmel Corporation 功能描述:Serial EEPROM, 2K x 8, 8 Pin, Plastic, SOP